[Jamming] Canon iRADV6065 jam code 0213 (jam type stnry: sensor no. 36)

[theorobz]

i have always got this jam message even when i print 1 page. i found the paper stock in the vertical side in left side of fixing unit going to duplex.

if i copy in the glass no any jam.
in adf it always jam and printing also.

i already clean the rollers and sensors. the machine counter 3.5million

any idea thnks much

[MunsterTech]

Re: Canon iRADV6065 jam code 0213 (jam type stnry: sensor no. 36)

have you tried from the bypass? is it the same for all cassettes?

[theorobz]

Re: Canon iRADV6065 jam code 0213 (jam type stnry: sensor no. 36)

have you tried from the bypass? is it the same for all cassettes?

yes all cassette the same. jam always . ...the operator told me sometimes its working well sometimes jam directly. i checked the jam status many jam error occurs.

maybe i should replace the roller reverse v.p.? i observed almost stock in the area.
any parts related to that problem that need to check and replaced aside from first roller reverse?

thanks for the response..

[MunsterTech]

Re: Canon iRADV6065 jam code 0213 (jam type stnry: sensor no. 36)

i am still a bit lost to the orginal post, if you copy from the Glass, it works ok? so if you do 100 copies from the glass it will copy all 100? but if you use the adf or print jobs it will jam every single time???

[theorobz]

Re: Canon iRADV6065 jam code 0213 (jam type stnry: sensor no. 36)

[QUOTE=MunsterTech;438498]i am still a bit lost to the orginal post, if you copy from the Glass, it works ok? so if you do 100 copies from the glass it will copy all 100? but if you use the adf or print jobs it will jam every single time???[/QUOTE

your right.
if i copy from the glass its ok (i tried only 50).
but in adf or printing job its jam even in bypass...

[Canuck]

Re: Canon iRADV6065 jam code 0213 (jam type stnry: sensor no. 36)

The reason it doesn't jam from glass is because it does face up delivery from the glass(one original). Open the external delivery assembly. Turn the white gear on the rear top of it...you will find it stiff probably. Remove the brass Oilite bushings for the delivery/reversal roller shaft(its driven by the white gear thru another gear or 2) and clean the inside of them with alcohol. They get gummed up and stall the delivery stepper motor. You can get an upgrade kit that replaces them with bearings. I am surprised it took so long to give you this jam... I usually seen it at around 1.5 million

[theorobz]

Re: Canon iRADV6065 jam code 0213 (jam type stnry: sensor no. 36)

The reason it doesn't jam from glass is because it does face up delivery from the glass(one original). Open the external delivery assembly. Turn the white gear on the rear top of it...you will find it stiff probably. Remove the brass Oilite bushings for the delivery/reversal roller shaft(its driven by the white gear thru another gear or 2) and clean the inside of them with alcohol. They get gummed up and stall the delivery stepper motor. You can get an upgrade kit that replaces them with bearings. I am surprised it took so long to give you this jam... I usually seen it at around 1.5 million

thanks so much for the response sir.
i already clean the gear you mention then i tried to test without replacing anytime but the same jam coming.

sir which part/s i need to replace? the two reverse roller, 2 pc. gear drive and stepper motor am i right?..
thanks so much

[MrB]

Re: Canon iRADV6065 jam code 0213 (jam type stnry: sensor no. 36)

Is this single sided or 2 sided jams
Could quite possible be the Delivery Reverse Drive assy
(The new assy has bearings now instead of the old bushings)

FM4-5138-010 - DELIVERY REVERSE DRIVE UNIT

[theorobz]

Re: Canon iRADV6065 jam code 0213 (jam type stnry: sensor no. 36)

sir good day thanks so much for the help i learned a new. the jamming solved by replacing FM4-5138-010 - DELIVERY REVERSE DRIVE UNIT and 2 (lower and upper) reverse roller.

thanks so much for bright ideas. God bless

[Canuck]

Re: Canon iRADV6065 jam code 0213 (jam type stnry: sensor no. 36)

3 million...yeah...rollers a good idea...but honestly all you had to do is clean the brass Oilite bushings...I have tons of these machines with over 3 million on them....never changed any delivery rolls...clean the bushings or install the bearing mod. Glad you got it fixed