224e DF-624 C8107

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • DigiMan
    Trusted Tech

    Site Contributor
    250+ Posts
    • Jan 2013
    • 262
    #1

    [Error Code] 224e DF-624 C8107

    Goodmorning everybody.

    I know its from the glass cleaning mechanism but i disabled it through ADF Scan Glass Contam.Set.
    After switching ADF Scan Glass Contam.Sensitivity to Not Set its supposed to stop working(as ive seen in other similar machines)
    but this one just doesnt want to stop,it keeps working and eventually pops the code.

    Will try a FW update,but any other thoughts?
    I don't like the new copier I just bought. It says "put face down" but every time I do it, it blinds my eyes.
    Tags: None
    • Gift
      Service Manager

      1,000+ Posts
      • Mar 2011
      • 2421
      #2
      Re: 224e DF-624 C8107

      Had this once - finally it turned out that the harness from the scanner glas cleaning drive motor/sensor was pretty squeezed factory-wise - not visible at first inspection since the harness runs below the feed area.

        Comment

        • DigiMan
          Trusted Tech

          Site Contributor
          250+ Posts
          • Jan 2013
          • 262
          #3
          Re: 224e DF-624 C8107

          Originally posted by Gift
          Had this once - finally it turned out that the harness from the scanner glas cleaning drive motor/sensor was pretty squeezed factory-wise - not visible at first inspection since the harness runs below the feed area.

          Thnks for the reply.
          Your saying that you had the code popping constantly?I can make some 10-20 copies it pops again.
          Open close door its ok and so on.
          Also that occured for you even after you switched it off(the cleaning mechanism)?
          I don't like the new copier I just bought. It says "put face down" but every time I do it, it blinds my eyes.

            Comment

            • Gift
              Service Manager

              1,000+ Posts
              • Mar 2011
              • 2421
              #4
              Re: 224e DF-624 C8107

              No at first it was very sporadically - later on the error appeared more often. Guess the harness, that was stucked between DF/plastic housings got more damaged during the time of operation.
              Haven't tried to turn off the machanism but I'm not shure if - even disabled - the machine might do try to perform a home position rund every now and then.

                Comment

                • CompyTech
                  Super Tech

                  500+ Posts
                  • Feb 2011
                  • 706
                  #5
                  Re: 224e DF-624 C8107

                  Had this code too, sporadic at first. I reseated the cable that goes from the motor to the adf board. Seems to have did the trick for now.

                  Sent from my Nexus 7 using Tapatalk

                    Comment

                    • CompyTech
                      Super Tech

                      500+ Posts
                      • Feb 2011
                      • 706
                      #6
                      Re: 224e DF-624 C8107

                      Originally posted by CompyTech
                      Had this code too, sporadic at first. I reseated the cable that goes from the motor to the adf board. Seems to have did the trick for now.

                      Sent from my Nexus 7 using Tapatalk
                      Ate my own words.. About a week ago, code came back and this time for good. I can confirm that the harness from the cleaning motor to the DFCB was pinched on the bottom of the DF unit, probably that way from the factory.

                        Comment

                        • giddyupngo
                          Trusted Tech

                          100+ Posts
                          • Oct 2014
                          • 109
                          #7
                          Re: 224e DF-624 C8107

                          I am getting a C8107 code on the DF-701 ADF. The bulletin KBA00030034 refers to only the DF-624 ADF, and says to replace the wire harness assembly A3CFPP6300.
                          The corresponding harness on the DF-701 is A3CEPP4K00. Has anyone had success replacing this harness on this ADF? Some other posts mention the cable from the ADF to the machine also.
                          Thanks

                            Comment

                            • giddyupngo
                              Trusted Tech

                              100+ Posts
                              • Oct 2014
                              • 109
                              #8
                              Re: 224e DF-624 C8107

                              Never mind, I found the problem. A screw vibrated loose and wedged the belt. What are the chances?

                              Sent from my SAMSUNG-SM-G930A using Tapatalk

                                Comment

                                • rrrohan
                                  Service Manager

                                  Site Contributor
                                  1,000+ Posts
                                  • Sep 2011
                                  • 1975
                                  #9
                                  Re: 224e DF-624 C8107

                                  Originally posted by giddyupngo
                                  Never mind, I found the problem. A screw vibrated loose and wedged the belt. What are the chances?

                                  Sent from my SAMSUNG-SM-G930A using Tapatalk
                                  0 chance but customer doesn't need to know that

                                    Comment

                                    Previous template Next
                                    Working...